Plumber's Essentials: What You Need for Bathtub Installation
Plumber's Essentials: What You Need for Bathtub Installation
Blog Article
What are your ideas with regards to How to Install a Bathtub?
Mounting a bathtub isn't exactly brain surgery, but it does require strong plumbing, woodworking, as well as sometimes, tiling skills. Changing an old tub with a new one is also a reasonably hard job. If the old bathtub is easily obtainable, the project can relocate quickly; if you need to open up a wall surface to remove the old bathtub as well as place the brand-new tub, the task is much harder. In either situation, the job is within a house handyman's abilities, although you will require a helper to vacate the old tub and set in the brand-new one. Ensure you have qualified yourself for the task and are comfortable attempting it. Rather than employing a service provider to take control of a halfway-completed job, it is far better to consider utilizing one prior to you start. Possibilities are you may require an expert plumber to make tube links.
This post will certainly aid you set up a new tub in your shower room if you have actually already purchased a brand-new bathtub as well as don't require to alter the setup of your previous water pipes.
Your devices as well as product checklist should consist of the following:
Removing Old Touches
If you require to replace old faucets with new ones as a part of your installment, then the first thing you should do is detach the water system. After doing so, turn on the taps to drain any kind of water staying in the system. The procedure of removing the existing taps can be fairly bothersome as a result of the restricted access that is commonly the case.
Utilize a container wrench (crowsfoot spanner) or a faucet device to undo the nut that links the supply pipelines to the taps. Have a fabric all set for the remaining water that will certainly come from the pipes. When the supply pipes have actually been removed, use the very same device to loosen up the nut that holds the taps onto the bath/basin. You will need to stop the single taps from turning during this process. As soon as the taps have been eliminated, the holes in the bath/basin will have to be cleansed of any type of old securing substance.
Before going on to fit the new faucets, compare the pipeline connections on the old faucets to the new taps. If the old faucets are longer than the brand-new taps, then a shank adapter is needed for the brand-new faucets to fit.
Suitable New Taps
If the tails of the brand-new faucets are plastic, after that you will certainly require a plastic connector to stop damage to the thread. One end of the connector fits on the plastic tail of the faucet as well as the various other end gives a link to the existent supply pipelines.
If you require to fit a monobloc, after that you will certainly require lowering couplers, which connects the 10mm pipeline of the monobloc to the typical 15mm supply pipeline.
Next, place the faucet in the mounting opening in the bath/basin making certain that the washers remain in location in between the faucet as well as the sink. Secure the faucet in place with the supplier supplied backnut. When the faucet is safely in position, the supply pipelines can be connected to the tails of the faucets. The faucets can either be linked by utilizing corrugated copper piping or with normal tap connectors. The former kind should be linked to the tap ends initially, tightening up just by hand. The supply pipes can later on be linked to the other end. Tighten both ends with a spanner after both ends have been connected.
Installing the Tub
Using the two wooden boards under its feet, place the bath tub in the needed position. The wood boards are practical in evenly spreading the weight of the bathtub over the location of the boards rather than focusing all the weight onto four small factors.
The following goal is to ensure that the bath tub is leveled all round. This can be achieved by inspecting the level as well as adjusting the feet on the bathtub up until the level checks out level.
To mount taps, fit all-time low of the furthest adaptable tap port to the proper supply pipeline by making a compression join; then do the exact same for the various other tap.
Activate the water and examine all joints and also new pipework for leakages and tighten them if required. Fill the bath tub and also check the overflow electrical outlet as well as the regular outlet for leaks.
Lastly, deal with the bathroom paneling as defined in the manufacturer's user's manual. Tiling and also sealing around the bathtub must wait until the tub has been utilized a minimum of once as this will resolve it right into its last position.
Planning for the Installment
To start with, the supporting structure provided with the bath ought to be fitted (if called for) according to the supplier's directions. Next, fit the taps or mixer to the tub. When fitting the tap block, it is necessary to make certain that if the faucet includes a plastic washing machine, it is fitted between the bathroom and the faucets. On a plastic bathroom, it is additionally reasonable to fit a sustaining plate under the taps system to avoid pressure on the tub.
Fit the adaptable tap ports to the bottom of the two faucets making use of 2 nuts and olives (occasionally provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and after that pass the outlet through the hole in the bath. Use the nut provided by the manufacturer to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the flexible overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which need to be fitted inside the bath. Make sure you make use of all of the provided washers.
Attach the trap to the bottom of the waste outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Link the bottom of the overflow tube in a similar manner.The bath need to currently be ready to be suited its last placement.
Tiling Around the Tub
In the location where the bathroom meets the tile, it is necessary to secure the accompanies a silicone rubber caulking. This is necessary as the fitting can relocate enough to fracture a rigid seal, triggering the water to penetrate the wall in between the bathroom and also the tiling, resulting in complications with wetness as well as feasible leaks to the ceiling listed below.
You can select from a range of coloured sealants to blend in your fixtures and also installations. They are offered in tubes and cartridges, and are capable of securing spaces up to a size of 3mm (1/8 inch). If you have a larger void to fill up, you can load it with spins of soaked newspaper or soft rope. Bear in mind to always load the tub with water before securing, to allow for the motion experienced when the bathtub remains in use. The sealer can fracture relatively very early if you do not take into consideration this movement before securing.
Alternatively, ceramic coving or quadrant ceramic tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are additionally conveniently readily available on the market. It is suggested to fit the floor tiles using water-resistant or water resistant sticky and also cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I am just very serious about How to Install a Bathtub and I hope you enjoyed our post. Enjoyed our post? Please share it. Let others find it. Thank you so much for your time invested reading it.
Need fast action? Report this page